Watch This: How Car Key Button Repair Is Taking Over And What We Can Do About It

Car Key Button Repair A damaged car key is a hassle. It is possible to call a 24-hour Locksmith Service or purchase a replacement remote. You may be able save money by repairing your old key fob instead of replacing it. This is particularly true if the issue is caused by an old switch or a damaged contact. Battery If the buttons on your key fob aren't responding when you pressing them, it could indicate that the battery is dead or is close to the end of life. It's simple to replace the battery yourself, rather than paying for a locksmith or dealership. First, locate the battery compartment. It is usually located on the backside of the key fob and might be hidden behind the cover, which slides out, or an access point that opens when you press the button. When the compartment is open you can see the small button cell battery. It's usually shaped as an oblong coin and is identified with the plus and minus signs. Remove the old battery and replace it with a new one. Check that the plus and minus symbols are aligned correctly. Once the battery is in place, close the compartment and snap the two halves of the key fob. Make sure to align the parts and snap them in place properly prior to closing the door and testing your keys. Press any of the buttons to confirm that they function correctly. If your remote key fob ceases working after replacing the battery, it might be experiencing other issues that require a different form of repair. Dropping the fob into a puddle can cause it to stop working. It could also be due to a malfunction with the internal electrical system or the need to be deprogrammed. See if you can find out if the issue is related to your key fob applying these other typical automotive troubleshooting methods. Switches There are various types of switches found in the car key fob according to the year and make. The older style keys have a chip that is visible inside the case. The modern keys function by transmitting signals to your car. Whatever the model of key, the buttons on the key can become worn out or damaged with normal use. This causes them to become difficult to press or even ineffective. If you press the button with force it can cause further damage. It could also stop the key from working in the future. If you are unable to get your key to function, try changing the batteries. If that doesn't help then you might need to clean your key fob and re-adjust the switches. These tiny electronic switches are more prone than larger parts of the key to break due to the fact that they are constantly tossed around. The switches feel rubbery and are coated with a film that conducts electricity. This film can be worn away over time. However, they're small and inexpensive to replace. The old ones are soldered onto the circuit board so you'll have to take care to remove them without causing any damage to anything else. Then, Learn Additional Here can solder the new ones in and then reassemble your fob. Do not use your car key fob for more than a couple of hours at a stretch and avoid leaving it visible. When you're not using your key, keep it in a secure place. If the issue continues to persist after you have cleaned your key fob replaced the battery and attempted to clean it, then you may need to talk to an expert locksmith. A professional locksmith can test the frequency of your key to see if it's still able to communicate with your vehicle, open and replace micro switches, alter cases, and more. Outer Case Key fobs spend many hours bouncing around and when the buttons aren't able to move upwards and downwards within the case they can get stuck or even broken. If cleaning the case using rubbing alcohol and a cotton swab doesn't work, it might be necessary to take off the case. If the contacts that the buttons touch are not suitable for the application, or if they are worn, adjusting them may be the only option. Certain keys have buttons made of rubber that wear away over time. The rubber stretches and nails cut into it, and the buttons become difficult to press. In this case the key may fail and it's time to replace the case or the buttons. This repair involves removing your remote, looking for the switch on the board, then heating the solder and carefully remove them. The circuit board then gets soldered with new buttons. The case can then be put back together with the horseshoe key blade piece is attached. The new buttons should be securely fitted into the case to keep them from falling out. Inner Case Since your key fob is prone to be tossed around and occasionally be pressed by accident and the buttons inside may get damaged or stuck over time. Using metallic tape and a hole punch you can usually solve this issue when your car is away from home when the key fob won't work, allowing you to unlock the doors, but not to start the engine. This simple fix will enable you to safely get back to your vehicle and continue your journey.